Re: Fried my Edison on the mini breakout...
Hi broody,after i had read this article from "Tage" i became rather skeptical about the max. usb current: https://communities.intel.com/message/256066#256066It sounds not like you can get up to 500 mA...
View ArticleRe: Widi & Windows 8.1 problems
Great, but which drivers? In my case nothing happened and I am still left with dead WiDi :-(....
View ArticleRe: Blinking ethernet connector at startup
Hi, The response to the cat command is0x01000200 The firmware states its for the edison board, not for Galileo. regardsCor
View ArticleIntel galileo Serial1.read problem......
Sir i am trying to communicate intel galileo with AVR atmega8 microcontroller..........The ATmega8 sends all bytes properly to MY PC (i am using Serial Terminal) at 9600 baud rate 1stop bit and no...
View ArticleRe: How best proceed with overheating i7-4790K?
HelloShadiElwanWhat are yourtemperaturesat idle?Are you sure1.125Vis static andthatit does not increasewhencpuloadIf indeedthe cpugoes upto 100°C with1.125andthat everything is doneproperly thenhe has...
View ArticleIntel DH61AG
Hi i want to buy mSATA SSD 240GB of any brand for my Intel DH61AG Mother BoardI am afraid, after buying if it is not compatible with this MB.Can any one help me which 240GB mSATA SSD's are Compatible...
View ArticleClik here to view.
Re: How best proceed with overheating i7-4790K?
helloallAt homeI haveseen(withthedefaultbiosand updated) when thecpuswitch toturbo(4400mhz) increasedthevcoreto1.31Vwhich had theeffect of havingtemperaturesclose to 100 °c. I havetherefore seekthe...
View ArticleRe: CDC serial driver issue
That's actually only the first partition of the SD card you see.
View ArticleThe new support page looks great!
The new support page looks very nice! Support CommunityThanks mark_h_@intel Doc
View ArticleRe: Problems using Fast Input using GPIO from linux
If the pull-up resistor is enabled (gpio0 is set to 1) then cat /sys/class/gpio/gpio14/valuealways returns 1, regardless of the voltage applied to IO2, and if pull-up resistor is disabled (gpio0 is set...
View ArticleRe: ubilinux (Debian) now available from Emutex Labs
Big thanks for the work here folks. Just some notes below on my experience trying to flash this.It took me a while to realize that xFSTK wasn't compiling because I was running on 14.04 64-bit. I...
View ArticleRe: How best proceed with overheating i7-4790K?
I thinkoftenthetemperaturedatafrom the softwarethat came withthe motherboard (ASUS Aifollowingexample)givesthe temperature of thecpuTo be confirmed. Eitherwaya temperature of100 °onthecoresprobably...
View ArticleRe: 525 series SSD not seen in BIOS or windows
More than a year later and there is not even an acknowledgment from intel that issue was confirmed. I am also affected with this bug and I would definitely appreciate any move with this case.
View ArticleXMP PROFILE 1.65V INTEL CPU I7 4790K
How safe is to use 24/7 the xmp profile for ram with 1.65v at 2400mhz Kingston Predator for cpu i7 4790k?Mobo is Asrock z87 extreme 4 and I have no issue at all when I activated xmp profile 2400mhz it...
View Articleno display after i install the r9 280x on my dh67bl motherboard.
Hi, I recently purchased a new asus r9 280x graphics card for my computer but i m not getting any display after i install the card. here is my computer specs.OS NameMicrosoft Windows 7...
View ArticleRe: Intel AC7260 limited access after sleep
I have the same problem too. I recently changed my network card from Wirless N-135 to AC7260 due to that I changed home network from 802.11n to 802.11ac. I have a MSI GE60 running Windows 7 64-bit....
View ArticleClik here to view.
Re: Blinking ethernet connector at startup
Hello Diego, I have just upgraded the firmware and got the message target firmware upgraded succesfully. But ... after plugging in my SDcard back and calling the cat command I got the same response as...
View ArticleRe: Problems using Fast Input using GPIO from linux
HI, with your hint I was able to fix the problem. The actual solution was to add: echo -n "4" > /sys/class/gpio/exportecho -n "out" > /sys/class/gpio/gpio4/direction echo -n "1" >...
View ArticleRe: WiDi image freezing on HDTV
Thank you so very much, alyons. How kind it is of you to suggest this. I was actually looking for a dongle device as an alternative, but was not aware of this one.
View Article